Dji S800 EVO Manuale Utente

Spreading Wings S800 EVO User Manual V 1.10 February 07, 2014 Revision www.dji.com

©2012 DJI Innovations. All Rights Reserved. 10 Mount Frame Arms Step 1 Step 2 Moto

(3) Please refer to (2) to make sure the arm is perfectly positioned. (4) Make sure to use appropriate strength to press down the buckle correctly. (

Mount Landing Gear By using a 2-position switch of R/C transmitter, you can control the landing gear to retract remotely. 1 Assembly & Connecti

1. Assemble the left and right parts respectively, and then fix the screws at the joints with appropriate thread locker. 2. Connect

3 Transmitter Setting Select a 2-position switch (default setting is OK) of Transmitter as the control input of the landing gear, and then make sure t

Tips (1) The system will turn off the servo power temporarily within 3 seconds after the landing gear has reached the target position. (2) When powe

5 Mount Battery Bracket Step1: Mount the retaining clip and the bracket, fix screws (but not tighten). M2.5X5Retaining ClipsChamfer OutwardsBracketNo

Assembly Assembly (2)①②③④⑤⑥(1)Vibration AbsorberCoaxial Align NotCoaxialAlign knob to markInsert knob into arm Rotate knobAircraft NoseMarkKnobVibrat

Install the IMU Mount (Optional) If you wish to achieve a smooth and steady fight, carry out the following procedures to install the IMU Mount. 1. (F

Appendix ESC Sound ESC State Sound Ready ♪1234567--B--B Throttle stick is not at bottom BBBBBB… Input signal abnormal B--------B--------B… Input volta

Disclaimer Thank you for purchasing this DJI product. Please regularly visit the S800 EVO web page at www.dji.com, which is updated regularly. Product

Specifications Frame Diagonal Wheelbase 800mm Frame Arm Length 350mm Frame Arm Weight (with Motor, ESC, Propeller ) 356g Center Frame Diameter 240mm

FAQ (Trouble Shooting) Solder ESC Make sure to solder the thick wires and fine wires correctly, when solder ESC to frame arm. Clockwise and counter

Spare Parts Listing If S800 EVO needs component replaced, please refer to the following diagram to identify the component NO., and then make a purchas

Center Frame M2.5x5(25pcs)M2x9(12pcs)SE021401(6pcs)SE021201SE021601(7pcs)SE021501SE021502SE021503SE021301SE021301M2.5x5(25pcs) Package NO. Name Compon

Landing Gear SE031701SE031702SE031801SE031901HC_M2 5x10 4pcs. ( )SE032001PM2 5x4.x3SE032901SE032201SE032202SE032204M2 5x5 4pcs. ( )SE032301SE032302M3x

26 Base Tube SE032601、SE032701 27 Silicone Rubber Damper SE032701 28 Damping Unit (Set) SE032801、SE032802、SE032803、SE032804、HC_M3x8 29 Aluminum Tube o

M2.5(4pcs)SE014401S 014402E Package NO. Name Components Number 44 Vibration absorber of Motor SE014401、SE014402、M2.5

Profile S800 EVO is a multi-rotor designed for aerial photograph which integrates reinforced mechanical structures, stabilized dynamical

Contents Disclaimer ...

Product Usage Cautions When flying, the fast rotating propellers may cause serious damage(s) and injuries. Therefore, please fly with a high safety in

In The Box Center Frame×1 Frame Arm×6 Retracting Mechanism×2 Landing Gear Support Tube ×2 Base Pipe×2 H Frame Connection Pipe×1、Spring×2 Packa

Center Frame Wiring The top board is a power distribution board, and the bottom board is for loading autopilot system components. Top BoardBottom Boar

Attach Electric Equipment to Center Frame 1. (Fig.1)Remove the screws in the bottom board. 2. (Fig.2)Attach the IMU module into IMU position

Fig.3 Fix the screws Note: for DJI A2 user, please use the component in red; for WKM user, it is not required. F